Nuvi 2495 LT koppel nie

[Robsan]

Hi,
Kan iemand raad gee ek het n nuvi 2495 aangeskaf maar dit wil nie op my rekenaar koppel nie, ek kan nie my waypoints laai nie ook nir RHD nie, ek het op Garmin express probeer maar geen sukses nie, wanneer ek dit wil ontkoppel is daar nie n ikoon wat wys nie, ek gebruik windows XP op my rekenaar ek gebruik ook n garman koord asook die een wat ek saam met die toestel ontvang het maar geen sukses nie sal bly wees as iemand raad het.
Dankie
Robsan

[Jan Horn]

Robbert dit lyk soos `n "driver' problem. Jy kan die "drivers" vir die 2495 hier aflaai. http://www.solvusoft.com/en/update/driv ... l-numbers/

[Robsan]

Hi Jan,
Dankie vir die raad ek het dit probeer maar dit werk nie, ek het vir garmin n e-pos gestuur en hier is die antwoord wat ek gekry ek het dit probeer en het reg gekom hy koppel nou, alles is nou reg.

On your GPS just make sure of one of the setting is on mass storage mode.

What you need to do is:

On your unit go to map.

Click on speed.

Press and hold in the middle of the circle for round about 10 seconds

A new page will come up then go to MTP Settings

Open MTP Settings and select mass storage and save.

The unit will connect to the PS via USB.

Kind regards
roete
Robert

[Jan Horn]

Dankie Robert. Mens is geneig om te vergeet van daardie een. Die eenhede kom gewoonlik gestel op “Mass Storage Mode”

[fugglefeet]

Robert,

Dankie vir daardie stukkie inligting. Dit kan nou iemand die frustrasie spaar om alles om te dolwe op soek na die antwoord vir dieselfde probleem.

Darryl

[Jan Horn]

Ek het so `n bietjie rond gesoek op Google. In sekere gevalle en op sekere maak PC's laai MTP drivers nie altyd nie. MTP staan vir Media Transfer Protocol. Hier is hulle voorstel om die probleem op te los.

Support Engineer
Hi,
Thank you for choosing Microsoft Community!
From your issue description I understand that, you are unable to connect external devices, where the MTP USB Device driver doesn't install.
I can imagine the inconvenience you have experienced. Don’t worry; we will certainly help you.
1. What is the make and model of your computer?
2. How did you install the devices?
Let’s follow these methods and check if it fixes the issue.
As all the hardware devices have drivers associated similarly USB devices also have it. Sometimes proper drivers do not get detected after the initial installation so reinstallation of the drivers helps resolve the issues.
You may check after uninstalling and reinstalling the USB drivers if you are able to connect. You may disconnect all USB devices and then perform the following steps:
a. Click Start, and then click Control Panel.
b. Click System and Maintenance, click System, and then click Device Manager.
Note: If Control Panel is in Classic View, double-click System, and then click Device Manager.
If you are prompted for an administrator password or for a confirmation, type the password, or click Allow.
c. In Device Manager, double click to expand "Universal Serial Bus controllers", right click on the Host Controller, click "Uninstall" and click "OK".
Check if at all there is an exclamation mark along the driver, it suggests issues with the driver installed.
d. Repeat the step 2 to uninstall all items under "Universal Serial Bus controllers".
Then, restart your computer and Windows 7 will reinstall all USB controllers automatically.
If you still face the same issue then you may check for the updated USB device drivers using windows update. Refer to the below link for assistance: http://windows.microsoft.com/en-us/wind ... g-properly
If the issue sill persists I would request you to check for chipset driver updates which you can get at the manufacturer website. The chipset drivers normally incorporate USB controller drivers as well.
Hope this will be helpful. If you still have further queries, please reply us and we will be happy to help you.